冷再生機是專門針對瀝青道路開展再生工藝的設備，然而設備的工作效率是與操作人員的正確操作分不開的，只有嚴格按照正規流程開展操作才能使設備發揮100%的效果，那么冷再生機的正確操作規程是什么呢？下面冷再生機出租廠家就來介紹一下。

A cold recycling machine is a device specifically designed for the recycling process of asphalt roads. However, the efficiency of the equipment is inseparable from the correct operation of the operators. Only by strictly following the formal process can the equipment achieve 100% effectiveness. So what is the correct operating procedure for a cold recycling machine? Let's introduce the rental manufacturers of cold regeneration machines below.

1.使用后控制面板時，需將開關調到后操控，此刻前控制面板無作用，除此之外每個小噴嘴開關能夠使用后控制面板開啟、關掉。

1. When using the rear control panel, it is necessary to set the switch to rear control. At this moment, the front control panel has no effect. In addition, each small nozzle switch can be turned on and off using the rear control panel.

2.設備不可以灌的過滿，給油口蓋務必關嚴，運送過程中防止瀝青溢出。

2. The equipment cannot be overfilled, and the oil supply port cap must be tightly closed to prevent asphalt overflow during transportation.

3.設備在噴撒前必須要查驗各閥門部位是否正確。添加設備內的熱態瀝青務必達標160~180℃的操作溫度，遠距離運送或工作時間太長，可應用升溫設備保溫，但不可以作為熔油爐。

3. Before spraying, the equipment must be checked to see if all valve parts are correct. The hot asphalt added to the equipment must meet the operating temperature of 160~180 ℃. If transported over long distances or working for too long, heating equipment can be used for insulation, but it cannot be used as a melting oil furnace.

冷再生機往前行駛時，轉子往上轉動銑刨原道路材料，與此同時，水通過軟管從聯接的水車中運輸進來，并在再生機的攪拌倉中噴撒。水的輸送量根據微處理器操縱的泵送系統精準控制，以達標所需要的水分含量。

When the cold regeneration machine moves forward, the rotor rotates upwards to mill and plane the raw road materials. At the same time, water is transported through a hose from the connected water truck and sprayed in the mixing bin of the regeneration machine. The delivery amount of water is accurately controlled by a microprocessor operated pumping system to meet the required moisture content.

銑刨轉子將水與銑刨料充足拌合。液體穩定劑可根據布置的噴撒嘴被噴撒到攪拌腔；粉末

The milling rotor adequately mixes water with the milling material. The liquid stabilizer can be sprayed into the mixing chamber according to the professionally arranged spray nozzle; powder

穩定劑如混凝土需按布置填加量事前噴灑在冷再生機前的道路上，冷再生機將粉末狀穩定劑與再生料和水一次性攪拌。如遇再造層原配合比欠佳的狀況，可在再生前將所缺乏的部分集料噴灑在道路上，根據與廢料加工攪拌來改進原地面材料的級配。

Stabilizers such as concrete need to be sprayed on the road in front of the cold recycling machine in advance according to the arrangement and dosage. The cold recycling machine will mix the powdered stabilizer with recycled materials and water in one go. If the original mix ratio of the reconstructed layer is not good, the missing part of the aggregate can be sprayed on the road before regeneration, and the grading of the original ground material can be improved by mixing it with waste processing.

以上就是冷再生機操作規程介紹的全部內容了，有關其操作流程就簡介這么多了，特性就是低成本、不毀壞地基等。希望文中的簡介能對大家有幫助。您有需求就來我們網站http://m.ebagshop.com.cn咨詢！

The above is the entire content of the introduction to the operating procedures for cold revitalization, and there are so many introductions about its operating procedures, with the characteristics of low cost and no damage to the foundation. I hope the introduction in the article can be helpful to everyone. Come to our website if you have any needs http://m.ebagshop.com.cn consulting service