一、日常清潔與保養

　　1、 Daily cleaning and maintenance

　　1. 清洗外表：冷再生機在施工過程中會積累大量灰塵和油跡，這些污染物不僅影響外觀，還可能成為腐蝕的誘因。因此，要定期清洗工程機械的柴油機、底盤、工作裝置的外表，保持其整潔。但注意，在清洗時嚴禁用高壓、高溫的水槍沖洗防水要求較高的部位，特別是電器部分，以免造成損壞。

　　1. Cleaning the appearance: During the construction process, the cold recycling machine will accumulate a large amount of dust and oil stains, which not only affect the appearance but may also become a cause of corrosion. Therefore, it is necessary to regularly clean the exterior of the diesel engine, chassis, and working equipment of construction machinery to maintain their cleanliness. However, it is strictly prohibited to use high-pressure and high-temperature water guns to rinse areas with high waterproof requirements, especially electrical parts, during cleaning to avoid damage.

　　2. 保養轉子及其罩殼和滑靴：

　　2. Maintain the rotor, its casing, and sliding shoes:

　　檢查轉子是否有水泥結垢等，及時清理灰塵，并對需要割除、焊接的刀具進行更換。

　　Check whether the rotor has cement scaling, clean the dust in a timely manner, and replace the cutting tools that need to be cut or welded.

　　清理轉子罩殼上的灰塵，并在施工結束收車時將轉子罩殼墊起地面5~10公分，防止雨雪的浸蝕。

　　Clean the dust on the rotor cover and place the rotor cover 5-10 cm above the ground to prevent erosion from rain and snow when the construction is completed and the vehicle is closed.

　　檢查滑靴的磨損情況，對已經磨損的部分進行補焊，并在螺紋處涂抹黃油防銹。

　　Check the wear of the sliding shoes, repair the worn parts with welding, and apply butter to the threads for rust prevention.

　　二、發動機維護

　　2、 Engine maintenance

　　1. 定期更換機油：機油是發動機的“血液”，定期更換機油是保持發動機正常運轉的關鍵。建議按照廠家的更換周期進行機油更換，同時選擇符合規格的機油，以確保發動機內部的清潔和潤滑。

　　1. Regularly changing engine oil: Engine oil is the "blood" of the engine, and regularly changing engine oil is the key to maintaining normal engine operation. It is recommended to change the engine oil according to the manufacturer's recommended replacement cycle, and choose oil that meets the specifications to ensure cleanliness and lubrication inside the engine.

　　2. 清潔空氣濾清器：空氣濾清器的作用是阻止空氣中的雜質進入發動機，防止發動機磨損。因此，要定期清潔或更換空氣濾清器濾芯。

　　2. Clean the air filter: The function of the air filter is to prevent impurities in the air from entering the engine and prevent engine wear. Therefore, it is necessary to regularly clean or replace the air filter element.

　　3. 檢查冷卻液：冷卻液的作用是保持發動機的正常工作溫度。應定期檢查冷卻液液位和質量，確保其處于正常范圍內。

　　3. Check the coolant: The function of coolant is to maintain the normal operating temperature of the engine. Regularly check the coolant level and quality to ensure it is within the normal range.

　　4. 緊固螺栓和螺母：發動機運行過程中，螺栓和螺母可能會因振動而松動。因此，要定期檢查并緊固螺栓和螺母。

　　4. Tighten bolts and nuts: During engine operation, bolts and nuts may loosen due to vibration. Therefore, it is necessary to regularly inspect and tighten bolts and nuts.

　　三、其他重要部件的維護

　　3、 Maintenance of other important components

　　1. 檢查易損件：如軸承、密封圈等，如有磨損或損壞應及時更換。

　　1. Check vulnerable parts such as bearings, sealing rings, etc. If there is wear or damage, they should be replaced in a timely manner.

　　2. 潤滑系統：定期檢查設備的潤滑系統，確保各運動部件得到充分潤滑，防止磨損和卡滯。

　　2. Lubrication system: Regularly inspect the lubrication system of the equipment to ensure that all moving parts are adequately lubricated and prevent wear and jamming.

　　3. 電氣系統：檢查電纜、控制器等電氣部件的連接情況，確保其正常工作。

　　3. Electrical system: Check the connection of electrical components such as cables and controllers to ensure their normal operation.

　　四、定期檢修與記錄

　　4、 Regular maintenance and recording

　　1. 制定維修計劃：根據設備的維護手冊制定維修計劃，定期更換磨損部件，確保設備正常運行。

　　1. Develop a maintenance plan: Develop a maintenance plan based on the equipment's maintenance manual, regularly replace worn parts, and ensure the normal operation of the equipment.

　　2. 記錄與報告：對設備的運行狀況和作業過程進行記錄，發現問題及時報告并處理。

　　2. Record and report: Record the operation status and operation process of the equipment, report and handle problems in a timely manner.

　　五、注意事項

　　5、 Safety precautions

　　1. 操作前準備：確保冷再生機各部件完好無損，無嚴重磨損或老化現象；檢查油、水、電氣等系統是否正常；檢查裝置是否齊全、有效。

　　1. Preparation before operation: Ensure that all components of the cold regeneration machine are intact and free from severe wear or aging; Check whether the oil, water, electrical and other systems are normal; Check if the safety devices are complete and effective.

　　2. 操作中的監控：在冷再生機運行過程中，應密切關注機器的工作狀態和周圍環境的變化。如發現異常情況或故障，應立即停止工作并進行檢查。

　　2. Monitoring during operation: During the operation of the cold regeneration machine, close attention should be paid to the working status of the machine and changes in the surrounding environment. If any abnormal situation or malfunction is found, the work should be stopped immediately and checked.

　　3. 操作后維護：每次使用后，應徹底清洗設備表面，去除灰塵、雜物和殘留物；檢查設備的潤滑系統；如設備出現異常聲音、振動或性能下降，應立即停機檢查并診斷故障原因。

　　3. Maintenance after operation: After each use, the surface of the equipment should be thoroughly cleaned to remove dust, debris, and residue; Check the lubrication system of the equipment; If the equipment produces abnormal sound, vibration or performance degradation, it should be stopped immediately for inspection and diagnosis of the cause of the fault.

　　總之，冷再生機的維護是一個綜合性的工作，需要細心、耐心和知識。只有這樣，才能確保冷再生機在施工中的、穩定運行。

　　In short, the maintenance of a cold regeneration machine is a comprehensive task that requires attention to detail, patience, and professional knowledge. Only in this way can we ensure the efficient and stable operation of the cold recycling machine during construction.

　　本文由冷再生機租賃提供幫助，更多的相關內容請點擊：http://m.ebagshop.com.cn希望本文能夠為您帶來幫助，感謝您的閱讀！

　　This article is assisted by Cold Recycling Machine Rental. For more related content, please click: http://m.ebagshop.com.cn I hope this article can be helpful to you. Thank you for reading!